Описание пользователя

Discuss with that product’s set up sheet for instructions. Twist and remove mounting bracket to insert battery. Product Description Lutron’s ceiling-mounted Occupancy Sensors are wireless, battery-powered, passive infrared (PIR) units that automatically management lights via RF communication with a dimming or switching system. These Sensors detect the heat from folks shifting within an space to find out when the house is occupied. The Sensors then transmit the appropriate commands to the associated dimming or switching device to turn the lights on or off routinely, providing both comfort and distinctive vitality financial savings. Sensor doesn't carry out satisfactorily from this location, it may be moved to 1.4 Ifanother location by pulling the Sensor straight down and repeating steps 1.Three and 1.4. 1.5 If the Sensor’s performance is passable, it ought to be completely connected to the ceiling tile, as described in part G. Permanent Mounting. Short-term Strong Ceiling Mounting Use this process if the Sensor shall be mounted on a strong, steady ceiling floor such as drywall, plaster, concrete, or wood. Two 3M™ Command™ adhesive strips are supplied for temporarily mounting and testing the Sensor on clean, solid ceiling surfaces. These strips are designed for simple, damagefree removing and usually are not reusable. These strips shouldn't be used for permanently mounting the Sensor (see section G. Permanent Mounting ). Fastidiously observe the elimination instructions under to ensure the ceiling isn't damaged throughout removing. Observe: Do not use the adhesive strips on ceiling tiles, as they will probably cause injury to the tile upon elimination. Straightforward-to-observe Instructions Set-Up To ensure that the Sensor to function properly, it must first be set up with a corresponding dimming or switching device. The process for organising a Sensor with a Maestro Wireless® (MRF2- only) Dimmer or Electronic Switch is detailed below. P/N 041-172a 2.1 Peel the pink "Command Strips" liner off of one of the adhesive strips and apply the strip to the flat aspect of the mounting bracket as proven within the diagram. Note: Do not cowl the bracket’s screw holes as a result of they are going to be used to mark screw gap places on the ceiling. Organising a Sensor with a Maestro Wireless Dimmer or Electronic Swap Dimmer Key Features · Low Maintenance. 10-12 months battery life. Convenient low-battery indicator. · Multiple Units. Up to three Sensors can work collectively to control lights for broader coverage in massive areas. Each Sensor may be added to up to 10 receiving gadgets. Sensor Operation Occupancy Version - The Sensor will routinely turn the lights on when the space is occupied and robotically flip the lights off after the space is vacated. The Sensor will automatically flip the lights off after the space is vacated. There is a constructed-in 15-second vacancy grace interval that begins when the lights are robotically turned off, during which the lights will routinely turn again on in response to motion. This grace interval is offered as a safety and convenience characteristic within the event that the lights flip off while the room continues to be occupied, in order that the consumer doesn't must manually turn the lights again on. After 15 seconds, the grace interval expires and the lights should be manually turned on. This Sensor is a part of a system and can't be used to regulate a load and not using a compatible dimming or switching system. Refer to the instruction sheets of the receiving device(s) for installation data. The Sensor could also be installed as much as 60 ft (18.Three m) away from the associated dimming or switching machine(s) if they're in direct line of sight. If there are walls or different limitations between the Sensor and receiving device(s), the Sensor must be positioned inside 30 ft (9.1 m). Warning: This product must not be used to manage tools which may create hazardous conditions, similar to entrapment, if operated by accident. Sensor in a location where it has a broad view outside the meant house. If that is unavoidable, the lens might be masked to block the view of undesired areas (confer with part I. Lens Masking). This guarantee is in lieu of all different express warranties, and the implied guarantee of merchantability is limited to one 12 months from purchase. This warranty doesn't cowl the cost of installation, elimination or reinstallation, or damage ensuing from misuse, abuse, or damage from improper wiring or set up. This guarantee doesn't cowl incidental or consequential damages. LUTRON’S Legal responsibility ON ANY Claim FOR DAMAGES ARISING OUT OF OR IN CON­NEC­TION WITH THE MANUFACTURE, SALE, Installation, Supply, OR USE OF THE UNIT SHALL By no means EXCEED THE PUR­CHASE Price OF THE UNIT. This guarantee gives you specific authorized rights, and chances are you'll produce other rights which vary from state to state. Some states don't allow the exclusion or limitation of incidental or consequential damages, or limitation on how lengthy an implied warranty could last, so the above limitations might not apply to you. Patents pending. Lutron, Maestro Wireless, and the Sunburst logo are registered trademarks and Radio Powr Savr is a trademark of Lutron Electronics Co., Inc. ANSI is a registered trademark of the American Nationwide Requirements Institute. IEC is a trademark of the Worldwide Electrotechnical Fee. Made and printed within the U.S.A. 25/09/09 P/N 041-172 Rev. A 8 ft (2.Four m) 18 x 18 ft (5.5 x 5.5 m) 13 ft (4.0 m) 9 ft (2.7 m) 20 x 20 ft (6.1 x 6.1 m) 14.5 ft (4.4 m) 10 ft (3.Zero m) 22 x 22 ft (6.7 x 6.7 m) sixteen ft (4.9 m) 12 ft (3.7 m) 26 x 26 ft (7.9 x 7.9 m) 19 ft (5.Eight m) Short-term Mounting Strategies 1.1 1.2 Insert the ceiling tile mounting wire by way of the 2 smaller holes in the mounting bracket and change the mounting bracket. Mount Sensor to a ceiling tile by inserting the wire legs through the tile, making sure the Sensor is flush to the tile. Word: Don't twist wire legs collectively. 1.2 After the Sensor has been temporarily mounted, leave the Sensor in place on the tile and either take the tile down or take away an adjoining tile to realize entry to the legs of the mounting wire on the back of the tile. Low Exercise: This is essentially the most delicate setting and can detect very slight motions. This is the recommended setting, as it would work properly for almost all purposes. It is right for spaces where occupants will typically be seated for lengthy durations of time. Twist the wire legs together tightly so the mounting bracket remains snug against the tile. This setting is barely much less sensitive than the Low Activity setting and can be utilized for areas that experience regular exercise. That is the least sensitive setting and can be utilized for areas that will usually only expertise large motions, corresponding to foot traffic. The Low Exercise setting is the default and can perform best for many functions. Not often, if the Sensor is positioned near external noise sources akin to heating vents, air conditioning vents, or gentle bulbs, it may flip the lights on with out occupancy or keep the lights on too lengthy after vacancy. If this occurs, changing the sensitivity to Medium Activity or Excessive Activity ought to resolve the problem. Change the tile. Everlasting Strong Ceiling Mounting 2.1 2.2 2.Three Superior Set-Up Operation The advanced set-up is accessed by using the buttons on the again of the Sensor. Drill two 3/sixteen in (4.6 mm) pilot holes for the supplied screw anchors. Press the anchors into the holes and tap flush with a hammer. To display the present setting, press and launch the specified button. An LED will illuminate briefly, indicating the current setting. Place the flat facet of the mounting bracket in opposition to the ceiling and set up the 2 offered screws utilizing a hand screwdriver. To regulate a setting, press and hold the desired button till the LED corresponding to the current setting begins flashing quickly, indicating the setting can now be adjusted. Each subsequent button press of less than 2 seconds will increment the mode to the following out there setting. Urgent any of the opposite buttons will haven't any impact. To avoid wasting the chosen setting, press and hold the button until the LED turns on stable, indicating the saved setting. Through the adjustment process, if there isn't any activity for 30 seconds, the LEDs will flip off and no settings will likely be saved. Observe: Do not over-tighten. 2.Four Attach the Sensor to the mounting bracket by inserting and twisting in a clockwise path till the Sensor locks into place. To remove the bracket from the ceiling, grasp the elimination tab on the adhesive strip and pull the tab VERY SLOWLY straight across the ceiling, stretching the strip till the bracket releases from the ceiling. Discard the strip. Never pull the strip at an angle, as it may break or harm the ceiling floor. Be aware: Do not pull at an angle. Lens Masking (Non-obligatory) At any time when attainable, the Sensor ought to be put in in a location the place it cannot easily see into areas outdoors the supposed area, comparable to hallways or adjoining rooms. If this situation can't be avoided, portions of the lens could also be masked with the offered labels to dam the Sensor’s view of the undesired areas. It's endorsed to take away the Sensor from the mounting bracket before applying Superior Set-Up (Elective) the masking labels. The Sensor options a number of superior set-up modes. For nearly all of installations, the default settings will present the perfect efficiency and you will not must make the most of the superior set-up. The Occupancy version of the Sensor has three adjustable superior set-up modes: Timeout, Auto-On, and Sensitivity. The Vacancy-Solely version has solely two modes (Auto-On not accessible). The default settings are listed under. The Sensor will be screwed onto the mounting bracket in several completely different orientations. Make sure to notice the Sensor’s orientation earlier than taking it down and exchange the Sensor in the same orientation to ensure the meant space gets blocked. Outer lens sections correspond to the detection regions furthest away from the Sensor, whereas internal sections correspond to regions nearer to the Sensor. Be careful when making use of the labels to avoid creating gaps between adjacent masked sections. The Sensor may detect movement by inadvertent gaps. All the time (Occupancy model solely) Timeout 30 min 15 min 5 min Auto-On All the time Low mild Disable Exercise Timeout 30 min 15 min 5 min Superior Set-Up Modes Auto-On Always Low gentle Disable Exercise Activity: Low Exercise Lens sections proven in white are masked with labels Timeout The Sensor will flip the lights off if no motion occurs all through the timeout interval. There are three out there timeout settings: 5, 15, and half-hour. Lens Mask Lens sections shown in grey haven't been masked Auto-On The automatic-on performance of the Sensor could be adjusted to regulate how the lights reply upon preliminary occupancy. There are three accessible settings: At all times, Low gentle, and Disable. Always: The lights will always turn on. Testing Sensor Coverage With the Sensor mounted on the ceiling, press and release the "Test: Sensor" button on the entrance of the gadget. The lens will glow briefly, indicating the test mode has been entered. Word: There is a heat-up period of roughly 40 seconds after the batteries are installed earlier than the test mode can be activated. If the button is pressed during this time, the lens will flash constantly until the warm-up period is full, and then the check mode might be robotically entered. Verify the protection space by walking via the space and observing the lens. The lens will glow solid each time movement is detected. If the lens stays off during movement, the Sensor can't detect motion at that location. Press and launch the "Test: Sensor" button again to exit the test mode. If the button shouldn't be pressed, the test mode will routinely time out quarter-hour after being enabled, or 5 minutes after the last detected movement if the room is vacated. If the Sensor has important trouble detecting movement through the check, it must be moved to another location and retested. If the Sensor nonetheless has poor detection from the new location, discuss with the Troubleshooting part. Temporary Drop Ceiling Mounting Use this process if the Sensor shall be mounted on a ceiling tile. The ceiling tile mounting wire is supplied for both non permanent and everlasting mounting of the Sensor to drop ceilings composed of multiple tiles. It's designed to allow momentary mounting, testing, and repositioning (if obligatory) of the Sensor with out damaging a ceiling tile. As soon as the Sensor’s remaining place has been chosen, the mounting wire could be twisted to lock the Sensor in place completely. If the Sensor protection and wireless communication checks have been efficiently accomplished, use the mounting bracket as a template to mark the screw hole areas with a pencil. Be aware: Pull very slowly. Max. Room Dimensions Radius of Protection for Full Protection at Ground If you are unsure about appropriately positioning the Sensor, the following momentary mounting and testing procedures are advisable to verify proper efficiency before permanently installing the Sensor. Sensor’s detection vary is dependent on the ceiling peak, as shown in the desk under. Discover: Do not disassemble, crush, puncture, or incinerate the batteries. Do not dispose of batteries in regular household waste. Please recycle, take to a proper battery disposal facility, or contact your local waste disposal supplier relating to local restrictions on the disposal or recycling of batteries. O NOT mount the Sensor within 4 ft (1.2 m) of HVAC vents or gentle bulbs installed below the ceiling line. Warmer rooms might reduce the Sensor’s means to detect occupants. Use only excessive-high quality lithium batteries, measurement CR123, three V (ANSI-5018LC, IEC-CR17345). Don't use rechargeable batteries. Using improperly rated batteries might damage the Sensor. For questions regarding the set up or operation of this product, name the Lutron Technical Help Middle. Please present precise mannequin number when calling. U.S.A. and Canada (24 hrs / 7 days) Setting the Occupancy Light Level (occupancy version, dimming devices solely) the Sensor to the mounting bracket by inserting and twisting in a clockwise 2.5 Attach course until the Sensor locks into place. Sensor protection and wireless communication assessments as described in 2.6 Perform sections E. Testing Sensor Protection and F. Testing Wireless Communication. The Sensor needs to be put in in a location where it has a superb view of all parts of the room. The Sensor requires line of sight to operate correctly. If you can not see the Sensor, it cannot see you. The Sensor can't see via glass objects corresponding to patio or shower doors. The vary and efficiency of the RF system is extremely dependent on a wide range of complex elements similar to: · Distance between system components · Geometry of the building construction · Construction of walls separating system components · Electrical equipment located close to system components Technical Help 2.2 Establish a location on the ceiling the place the Sensor will have a good view of the room. 2.Three Take away the black "wall side" liner from the adhesive strip. The Sensor is designed for ceiling use solely. Don't set up on ceilings increased than 12 ft (3.7 m) or non-ceiling surfaces. Doing so might considerably inhibit the Sensor’s efficiency. 4. Don't paint Sensor. · · · · The "Lights On" and "Lights Off" buttons ought to now change the lights in the room on and off, respectively, when pressed. Repeat the above process to set up the Sensor with any further units. The Sensor is intended for indoor use only. Operate between 32 °F and 104 °F (0 °C and 40 °C). 1.1 a number of seconds. Sensor that has been arrange. After approximately 6 seconds, the lens will flash rapidly a number of occasions, indicating the light stage has been saved. All Sensors arrange with the Dimmer will now use the saved occupancy mild level. 2. Clear Sensor with a gentle damp cloth only. Do not use any chemical cleaners. Note: This gear has been examined and found to adjust to the boundaries for a class B digital system, pursuant to part 15 of the FCC guidelines. These limits are designed to provide reasonable safety in opposition to harmful interference in a residential set up. This tools generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, might cause dangerous interference to radio and television reception, which can be determined by turning the equipment off and on. The person is encouraged to try to appropriate the interference by one or more of the next measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Join the equipment into an outlet on a circuit totally different from that to which the receiver is linked. Consult the vendor or an experienced radio/Television technician for assist. Warning: Adjustments or modifications not expressly accepted by Lutron Electronics Co. could void the user’s authority to function this tools. This device complies with Part 15 of the FCC rules. This gadget should accept any interference received, together with interference that will cause undesired operation. Switch 2.1 Set the Dimmer to the desired mild stage for entering the room. 2.2 Save holding the "Lights On" button on the front of a Notice: For both Sensor model, the lights can also be manually turned off at any time by utilizing the dimming or switching machine straight. Necessary Notes or Add the Sensor to the Dimmer or Change by pressing and holding the "Lights Off" button on the entrance of the Sensor for approximately 6 seconds until the lens flashes briefly. The lights in the room will even flash three times, indicating the Sensor has been successfully added. The Dimmer or Switch will exit set-up mode routinely. The sensitivity of the Sensor might be adjusted primarily based on the expected level of exercise within the room. There are three obtainable exercise settings: Low Exercise, Medium Activity, and High Exercise. Everlasting Drop Ceiling Mounting Word: Depart the removal tab uncovered past the sting of the bracket so it can be accessed for removing later. 6 seconds till all LEDs on the gadget begin flashing. Launch the tap button. Sensor is detecting movement in areas that are not fascinating, akin to hallways or adjacent rooms, consult with part I. Lens Masking. If Sensor detection is passable during this check, perform the wireless communication take a look at as described in section F. Testing Wireless Communication. Testing Wireless Communication This take a look at needs to be carried out to verify that the Sensor has been accurately set up with the corresponding dimming or switching gadget and that there is proper wireless communication from the chosen Sensor location. If the lights within the room will not be on, turn them ON manually on the dimming or switching machine. Press and release the "Lights Off" button on the entrance of the Sensor. The lights ought to flip OFF. Press and launch the "Lights On" button on the front of the Sensor. The lights should turn on. If the lights don't respond appropriately, confer with the Troubleshooting part. Low gentle: The lights will solely turn on mechanically upon entry if there will not be already sufficient ambient mild in the room. Hallway falls inside Sensor’s protection space. Disable: This setting converts the Sensor to vacancy mode. The lights will not automatically activate however will nonetheless robotically flip off after vacancy. The lights have to be manually turned on by using the related dimming or switching machine. Be aware: The 15-second vacancy grace interval is energetic in this mode. Confer with the Sensor Operation part initially of this document for more particulars. Troubleshooting Symptom Potential Causes Solution Lights do not turn on when house is occupied. Sensor shouldn't be correctly added to dimming / switching gadget(s). Sensor’s Auto-On setting is ready to "Low light" or "Disable". The lights had been recently turned off manually and the timeout has not but expired. Sensor does not have full view of room. Sensor is outdoors wireless range of dimming/switching system. Check with section B. Set-Up. Refer to part H. Advanced Set-Up. Dimming/switching device has been improperly wired. Gentle bulb(s) burned out. Breaker is off or tripped. Sensor’s timeout is too brief for this application. Sensor does not have full view of room. Lens mask is improperly utilized. Sensor’s sensitivity is simply too low. Sensor’s timeout has not but expired. An external noise source resembling an HVAC vent is interfering. Discuss with section A. Pre-Set up. Habits of lights does not match Sensor settings. Sensor coverage extends past room perimeter. The meant setting was not saved. Multiple Sensors are added to a dimming/switching device and their settings don't match. Check with section A. Pre-Set up. Refer to part C. Sensor Placement or I. Lens Masking. Seek advice from part H. Superior Set-Up. Discuss with part H. Superior Set-Up. Sensor lens doesn't glow in response to movement throughout Sensor protection testing. Sensor can't see movement as a result of obstruction. Room is just too large or oddly shaped. Transfer Sensor to a different location. Refer to section C. Sensor Placement. Multiple Sensors may be obligatory for full room coverage. Strive shifting Sensor to a new location or decreasing sensitivity. Seek advice from section C. Sensor Placement or H. Advanced Set-Up. Lights turn OFF whereas house is occupied. Lights stay ON after space is vacated. Lens does not cease glowing throughout Sensor protection testing even when there is no such thing as a motion. Lights do not reply correctly during wireless communication testing. Sensor lens flashes and lights do not activate when area is occupied. Battery has been installed incorrectly. An external noise source akin to an HVAC vent is interfering. Discuss with part C. Sensor Placement. Check with section C. Sensor Placement or F. Testing Wireless Communication. Check with part H. Superior Set-Up. Confer with section C. Sensor Placement. Consult with section I. Lens Masking. Check with part H. Advanced Set-Up. Discuss with part H. Superior Set-Up. Strive moving Sensor to a new location or reducing sensitivity. Refer to section C. Sensor Placement or H. Advanced Set-Up. Sensor shouldn't be accurately added to dimming / switching system. Sensor is outdoors wireless vary of dimming/switching machine. Confer with section B. Set-Up. Transfer Sensor closer to dimming/switching system and retry check. Discuss with section F. Testing Wireless Communication. Battery has been installed incorrectly. Dimming/switching system has been improperly wired. Gentle bulb(s) burned out. Breaker is off or tripped. Battery is low. Confer with section A. Pre-Set up. Remove sensor from check mode. Discuss with part E. Testing Sensor Coverage.

If you have virtually any inquiries relating to exactly where in addition to the best way to make use of sc.sie.gov.hk, it is possible to email us in our web-page.